Cité du Cinéma (St Denis) Surface area: 3,300 m²
LE HAVRE, architecte cabinet QUATRE PLUS Paris - 1000m²
BARENTIN 33logts, Architect ATELIER DU CAP Cany-Barville - 1000m²
WASQUEHAL (Renovation of a restaurant in Lille), Architect POPIEUL Bruno LILLE
Nord region
Le Havre, Habitat 76 , Architect CBA (Rouen) - 1600m²
Nord region
Montreuil sous Bois, Bouygues Immobilier - 2200m²
Nord region
NANTERRE APOLLONIA - 1200m²
LE MANS (Résidence Val d'Huine) - 10 000m²
CHANTELOUP LES VIGNES - 1800m²
MANTES LA JOLIE - 5300m²


VETAbric:
The SLIMLINE brick facing panel
which can be adapted to any type of insulation
that meets architectural, economic and environmental constraints.

The VERY FINE brick facing panel

Fitting principles

Principles for fitting VETAbric panels in the case of prefabricated cladding on add-on insulation
Stage 1: Fitting the start section

At the base of the wall, an aluminium section has to be fastened. The width of this section depends on the thickness of the panel and of the insulation in-between. Any flatness defects in the support should not exceed 5 mm on a 20 cm rule. Should this not be the case, preparation must be carried out (sanding, resurfacing, etc.)

Stage 2: Fastening the panel

The panels are fastened using wall plugs and screws compatible with the support and the thickness of the insulation in-between. These fastenings are laid out in the grouting in-between the facing bricks.

Stage 3: Assembling the panels

The panels are laid out row by row with continuous or offset joins. The panels are assembled vertically by interlocking them. Horizontally, a rebate system enables the panels to be made waterproof.

Stage 4: Handling façades’ corners

Façades’ corners may be handled either using corner panels with or without interlocking, or using aluminium sections.

Stage 5: Handling openings’ corners

Openings’ corners can be handled using corner panels with or without interlocking, using aluminium sections or any other framing system.

Stage 6: Cutting the panels

The cutting to be carried out in order to lay out the assembly can easily be done using a jig saw or an angle grinder equipped with appropriate blades and disks. For a perfect assembly of the cuts and of the panels, polyurethane filler should be applied in-between the pieces.

Stage 7: Grouting the panels

The final grouting can be done in two different ways depending on the model of brick involved:

  • The traditional way, using a grouter on any type of facing brick.
  • The tilesetter's way, using a grouting kit on smooth facing bricks.

 

General points about fitting

The VETAbric system is used for prefabricated cladding or normal cladding. With or without add-on insulation


VETAbric mounting principle (prefabricated cladding on add-on insulation) on concrete or masonry


VETAbric mounting principle (simple prefabricated cladding) on concrete or masonry


VETAbric mounting principle (cladding) on concrete or masonry


Mounting items

Wall plugs and screw

Specially designed Wall plugs and screws that firmly fasten the VETAbric components to the support

Section

An aluminium section with a water run-off fitting fully protects the base of the facing and of the insulation.

Quality bricks

Each panel consists of a thin polyurethane support into which high-quality terracota facing bricks are set.

Additional insulation

Additional insulation is fastened onto the wall as a preliminary to further cladding using either adapted wall plugs/nails or is glued on.

 

VETAbric mounting examples

Mounting example involving an opening support using an aluminium skirt
Mounting example involving an opening frame using an aluminium section
Mounting example involving a reveal using VETAbric corner pieces
Mounting example involving a re-entrant corner piece
Mounting example featuring a façade corner piece using an aluminium section
Mounting example of waterproofing with roofing
Parapet mounting with an aluminium opening
Example of execution of a cornice

Pavillon

Renovate, embellish
and insulate your façade or house front externally

imgresReady to install brick
facings delivered!


Private individuals access

 

VETA France: A French manufacturer of brick panels for renovating and insulating façades and house fronts from the outside.

©2021 VETA France